• Marlo Water Softeners Commercial

Cleaning the Nozzle and Venturi

Water Softener Operating & Maintenance Instructions: How to set & adjust a water softener or water conditioner. Here we provide an owner's guide to water softener controls, what they are, what they do, how to set them - for water softener or water conditioner maintenance, including water softener adjustment of the regeneration or backwash cycle frequency and the water softener salt dose. Products like Marlo Inc.' S water softener systems soften hard water by removing the calcium and magnesium. Step 1 Fill the brine tank with water until the water level reaches 2 inches above the salt platform. Video of the Day. Water softener brine tanks: This article provides a table listing common problems, causes, and remedies for water softener brine tanks. Find out what causes too much water in the water conditioner brine tank or salt tank or too little water. View and Download Marlo Incorporated MGT Series installation, operation and maintenance manual online. SYSTEM 14 – DEMAND 2” NXT2 SERIES COMMERCIAL WATER CONDITIONER. MGT Series water filtration systems pdf manual download. Also for: Mgt 60m, Mgt 90m, Mgt 120m, Mgt 150m, Mgt 210m, Mgt. A clean nozzle and venturi are important for your water softener to work properly. This small unit creates the suction to move brine from the brine tank into the resin tank. If it should become plugged with sand, silt, dirt, etc., the conditioner will not work and you will get hard water.

A clean nozzle and venturi are important for your water softener to work properly. This small unit creates the suction to move brine from the brine tank into the resin tank. If it should become plugged with sand, silt, dirt, etc., the conditioner will not work and you will get hard water.

• To get to the nozzle and venturi remove the top cover. Be sure the unit is in its normal operating cycle/soft water cycle (no water pressure at nozzle and venturi). Then, holding the nozzle and venturi housing with one hand, turn off the cap. Do not lose the O-ring seal. Lift out the screen support and screen. Then remove the nozzle and venturi.
• Wash the parts in warm, soapy water and rinse in fresh water. If needed, use a small brush to remove iron or dirt. Be careful not to scratch, misshape, etc., surfaces of the nozzle and venturi. Also, check and clean the gasket and flow plug(s).
• Carefully replace all parts in the correct order. Lubricate the O-ring seal with silicone grease and locate in position. Install and tighten the cap, by hand only. Do not over-tighten and break the cap or housing.

Breaking A Salt Bridge

Sometimes a hard crust or “salt bridge” forms in the brine tank and leaves a hollow area below this salt in your water softener, usually caused by high humidity or using the wrong kind of salt. When the salt bridges, the salt is unable to dissolve in the water beneath to make a brine. Without the brine, the resin bed does not regenerate and you will have hard water.

If the storage tank is full of salt, it is hard to tell if you have a salt bridge. Salt is loose on top, but the bridge is under it. Take a broom handle, or like tool, and push it straight down into the salt. If a hard object is felt, it’s most likely a salt bridge. Carefully push into the bridge in several places to break it. DO NOT use any sharp or pointed objects to break a salt bridge as you may puncture the tank.

If you’re experiencing other issues please visit our Troubleshooting Guide or contact Customer Service for additional help.

We recommend regular use of Morton Clean and Protect™, Clean and Protect™ Plus Rust Defense™ or Morton Pure and Natural™ salt in all water softeners.

product specifications

Marlo Water Softeners Commercial

• Approximate Dimensions*

  Width	NA'
  Height	42'
  Depth	NA'
  Weight	NA lbs

  *refer to physical product for exact dimensions
• Shipping Dimensions

  Width	NA'
  Height	NA'
  Depth	NA'
  Volume	cu. ft.
  Weight	91.01 lbs

• Warranty

  Warranty

  • Limited 5 year parts and labor warranty • See manufacturer site for exact warranty specifics

• General

  Color
  Manufacturer Color
  Maximum Hardness After Filtration	grains/gal
  Maximum Iron After Filtration	ppm
  Total Hardness Capacity	30,448 grains
  Salt Storage Capacity	250 lb
  Minimum pH
  Maximum PH
  Maximum Flow Rate	15 gal/min
  Plumbing Connection	3/4,1'
  Operating Temperature Range	110 F
  Water Pressure	30-125 PSI psi
  Additional Information	• Fully assembled and ready for installation • Bypass and 1' brass sweat fittings included • Soft water refill reduces cleaning of brine tank • Lockout feature limits programming access • Variable reserve self-adjusts to usage level • Stores system data in non volatile memory • Brine Safety Float included
  Energy Star Certified

• Regeneration

  Grains Removed
  Water Required	2.7 gal
  Length of Cycle	minutes
  Salt Required	min. 5/max. 15 lb

• Electrical Information